一、鋁合金板的低溫形變熱處理簡介
1、 Brief introduction of low temperature thermomechanical treatment of aluminum alloy plate
低溫形變熱處理又稱為形變時效。廣泛的處理方式有：
Low temperature thermomechanical treatment is also called deformation aging. A wide range of treatment methods are as follows:
①淬火一冷(溫)變形一人工時效；
① Quenching cold (warm) deformation artificial aging;
②淬火一自然時效一冷變形一人工時效；
② Quenching natural aging cold deformation artificial aging;
③淬火一人工時效一冷變形一人工時效。
③ Quenching artificial aging cold deformation artificial aging.

冷變形造成位錯網絡，使脫溶相形核更為廣泛和均勻，有利于提高合度和塑性，有時也可提高鋁合金板的抗蝕性。
Cold deformation results in dislocation network, which makes the nucleation of desolvent phase more extensive and uniform, which is beneficial to improve the cohesion and plasticity, and sometimes the corrosion resistance of aluminum alloy plate.
二、鋁合金板冷變形對失效過程的影響
2、 Effect of cold deformation on failure process of aluminum alloy plate
1、冷變形對鋁合金板時效過程的影響規律較為復雜。它與淬火、變形和時效規程有關，也與鋁合金板本性有關。對同一種合金來說，與時效時沉淀相類型有關，簡言之，主要依靠形成彌散過渡相而強化的合金，時效前冷變形會使合金強度提高。這類合金淬火后，經冷變形再加熱到時效溫度時脫溶與回復過程同時發生。
1. The effect of cold deformation on the aging process of aluminum alloy sheet is complex. It is related to the rules of quenching, deformation and aging, and also to the nature of aluminum alloy plate. For the same alloy, it is related to the type of precipitation phase during aging. In short, for the alloy strengthened mainly by forming dispersed transition phase, cold deformation before aging will improve the strength of the alloy. After quenching, the desolvation and recovery occur simultaneously when the alloy is heated to aging temperature after cold deformation.
脫溶將因冷變形而加速，脫溶相質點將因冷變形而更加彌散。與此同時，脫溶質點也阻礙多邊化等回復過程。若多邊化過程已發生，則因位錯分布及密度的變化，脫溶相質點的分布及密度也會發生相應的改變。
The desolvation will be accelerated by cold deformation, and the desolvation phase particles will be more dispersed by cold deformation. At the same time, the desolvent point also hinders the recovery process such as multilateralization. If the multilateralization process has taken place, the distribution and density of particles in the desolvent phase will also change with the change of dislocation distribution and density.
2、低溫形變熱處理亦可采用溫變形。在溫變形時動態回復進行得相當激烈，有利于提高鋁合金板形變熱處理后材料組織的熱穩定性。低溫形變熱處理對Al-Cu-Mg系合金特別有用。
2. Warm deformation can also be used in low temperature thermomechanical treatment. The dynamic recovery is very intense during warm deformation, which is beneficial to improve the thermal stability of the material after thermomechanical treatment. Low temperature thermomechanical treatment is especially useful for Al Cu Mg alloys.
例如，2A12合金鋁板淬火后變形20%,然后在130℃時效10~20h,與常規熱處理比較，抗拉強度可提高60N/mm2,屈服強度可提高100N/mm2塑性尚好2A11鋁合金板淬火后在150℃軋制30%,然后在100℃時效3h,與淬火后直接按同一規范時效的材料相比，抗拉強度提高50N/mm2,屈服強度提高130N/mm2,但A值降低50%。
For example, 2A12 aluminum alloy plate is deformed by 20% after quenching, and then aged at 130 ℃ for 10 ~ 20h. Compared with conventional heat treatment, the tensile strength and yield strength of 2A12 aluminum alloy plate can be increased by 60N / mm2 and 100N / mm2 respectively, and the plasticity is still good. 2A11 aluminum alloy plate is rolled at 150 ℃ after quenching, and then aged at 100 ℃ for 3h. Compared with the material aged directly according to the same specification after quenching, the tensile strength and yield strength of 2A12 aluminum alloy plate are increased by 50N / mm2 and 130n / mm2 respectively, But a value decreased by 50%.